DataSheet.in

HFBR-53D5 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - 1 x 9 Fiber Optic Transceivers - Avago

भाग संख्या HFBR-53D5
समारोह 1 x 9 Fiber Optic Transceivers
मैन्युफैक्चरर्स Avago 
लोगो Avago लोगो 
पूर्व दर्शन
1 Page
		
<?=HFBR-53D5?> डेटा पत्रक पीडीएफ

HFBR-53D5 pdf
Package and Handling Instructions
Electrostatic Discharge (ESD)
Flammability
The HFBR/HFCT-53D5 transceiver housing is made of
high strength, heat resistant, chemically resistant, and
UL 94V-0 flame retardant plastic.
Recommended Solder and Wash Process
The HFBR/HFCT-53D5 is compatible with industry
standard wave or hand solder processes.
Process plug
This transceiver is supplied with a process plug (HFBR-
5000) for protection of the optical ports within the
duplex SC connector receptacle. This process plug
prevents contamination during wave solder and
aqueous rinse as well as during handling, shipping and
storage. It is made of a hightemperature, molded
sealing material that can withstand 80°C and a rinse
pressure of 110 lbs per square inch.
Recommended Solder fluxes Solder fluxes used with
the HFBR/HFCT-53D5 should be water-soluble, organic
fluxes. Recommended solder fluxes include Lonco
3355-11 from London Chemical West, Inc. of Burbank,
CA, and 100 Flux from Alpha-Metals of Jersey City, NJ.
Recommended Cleaning/Degreasing Chemicals
Alcohols: methyl, isopropyl, isobutyl.
Aliphatics: hexane, heptane Other: soap solution,
naphtha.
Do not use partially halogenated hydrocarbons such as
1,1.1 trichloroethane, ketones such as MEK, acetone,
chloroform, ethyl acetate, methylene dichloride,
phenol, methylene chloride, or N-methylpyrolldone.
Also, HP does not recommend the use of cleaners that
use halogenated hydrocarbons because of their
potential environmental harm.
Regulatory Compliance
(See the Regulatory Compliance Table for transceiver
performance)
The overall equipment design will determine the
certification level. The transceiver performance is
offered as a figure of merit to assist the designer in
considering their use in equipment designs.
There are two design cases in which immunity to ESD
damage is important. The first case is during handling
of the transceiver prior to mounting it on the circuit
board. It is important to use normal ESD handling
precautions for ESD sensitive devices. These
precautions include using grounded wrist straps, work
benches, and floor mats in ESD controlled areas. The
transceiver performance has been shown to provide
adequate performance in typical industry production
environments.
The second case to consider is static discharges to the
exterior of the equipment chassis containing the
transceiver parts. To the extent that the duplex SC
connector receptacle is exposed to the outside of the
equipment chassis it may be subject to whatever
system-level ESD test criteria that the equipment is
intended to meet. The transceiver performance is more
robust than typical industry equipment requirements
of today.
Electromagnetic Interference (EMI)
Most equipment designs utilizing these high-speed
transceivers from Avago Technologies will be required
to meet the requirements of FCC in the United States,
CENELEC EN55022 (CISPR 22) in Europe and VCCI in
Japan. Refer to EMI section (page 5) for more details.
Immunity
Equipment utilizing these transceivers will be subject
to radio-frequency electromagnetic fields in some
environments. These transceivers have good immunity
to such fields due to their shielded design.
Eye Safety
These laser-based transceivers are classified as AEL
Class I (U.S. 21 CFR(J) and AEL Class 1 per EN 60825-1
(+A11). They are eye safe when used within the data
sheet limits per CDRH. They are also eye safe under
normal operating conditions and under all reasonably
forseeable single fault conditions per EN60825-1.
Avago Technologies has tested the transceiver design
for compliance with the requirements listed below
under normal operating conditions and under single
fault conditions where applicable. TUV Rheinland has
granted certi-fication to these transceivers for laser eye
safety and use in EN 60950 and EN 60825-2
applications. Their performance enables the
transceivers to be used without concern for eye safety
up to 7 volts transmitter VCC.
2

विन्यास 18 पेज
डाउनलोड[ HFBR-53D5 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
HFBR-53D51 x 9 Fiber Optic TransceiversAvago
Avago


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English