DataSheet.in

IS1000E-202 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - Mechanical Style Pressure Switch - SMC

भाग संख्या IS1000E-202
समारोह Mechanical Style Pressure Switch
मैन्युफैक्चरर्स SMC 
लोगो SMC लोगो 
पूर्व दर्शन
1 Page
		
<?=IS1000E-202?> डेटा पत्रक पीडीएफ

IS1000E-202 pdf
Series IS1000
Construction
t
q
w
R 1/8
23
u
y
0.1
0.2
0.3
0.4
i
MPa
!0 IS1000
o
e
r
15
Component Parts
No. Description
q Shield plate
w Switch assembly
e Piston
r PT fittings
t Adjusting screw
y Pointer
u Spring
i Scale plate
o Miniseal Y type
!0 Magnet
Material
Rolled steel plate
Polyacetal
Zinc die-casted
Brass
Brass
Stainless steel 304-WPB
Rigid vinyl chloride
NBR
Rare earth magnet
Precautions
Be sure to read before handling. Refer to pages 16-14-3 and 16-14-4 for Safety Instructions and Common
Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-1-13 for Precautions on
every series.
Wiring
Warning
1. Connect load before connecting with power
source.
2. In the case of induction load or lead wire ex-
ceeding 5 m long, the following contact protec-
tion box should be used. It may lead to dam-
age to a switch.
Part no.
CD-P11
CD-P12
Voltage Lead wire length
100 VAC Switch side: 0.5 m
24 VDC Load side: 0.5 m
4. How to connect contact protection box
Connect the lead wires from the body and the
contact protective box side indicated
“SWITCH”. Lead wire should be as short as
possible, within 1 m.
5. Dimensions of lead wire
Enclosure: ø 3.4
Insulator: ø 1.1
Conductor: ø 0.64
Mounting/Piping
3. Internal circuit of contact protection box
Surge
absorber
CD-P11
Choke
coil
Brown
Blue
Condenser
CD-P12
Choke
coil
(+) Brown
Warning
1. When changing piping by hand, hold body.
Electrical wire must not be subjected to exces-
sive force.
It may cause a malfunction or damage.
2. Do not drop nor apply excessive force.
It may cause a malfunction or damage.
3. Tighten IS1000-01 applying the spanner on
the PT fitting part.
Resistance
(–) Blue
4. Mounting direction is available in either
horizontal or perpendicular.
Pressure Source
Warning
1. Do not use with corrosive gases or fluids.
2. Never use in an environment where flamma-
ble fluid or gas is used. Since this is not an
explosion-proof construction, it may lead to an
explosive disaster.
3. Avoid use in vacuum applications.
Switch may be imploded.
Pressure Setting
Warning
1. Scale of switching set display is the set value
at the pressure drop.
2. When detecting ON-pressure signal, note that
set pressure on scale plate plus ON-OFF differ-
ential (Hysteresis) will be ON-pressure signal.
3. Pressure display on the scale plate is just as a
reference guide. For an accurate setting,
measure it by pressure gauge.
Operating Environment
Warning
1. Avoid using a switch in a magnetic environ-
ment. It may cause a malfunction.
2. Do not use in such an environment, where
water or oil is splashed. Since it is the open
type construction, if water or oil make an
ingress into the internal parts, the electric
circuit will be corroded and may result in a
malfunction or damage.
3. Avoid vibration. Vibration may cause malfunc-
tion or may cause setting to be incorrect.
16-9-2

विन्यास 15 पेज
डाउनलोड[ IS1000E-202 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
IS1000E-201Mechanical Style Pressure SwitchSMC
SMC
IS1000E-202Mechanical Style Pressure SwitchSMC
SMC


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English