DataSheet.in

HIP4011 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - Three Phase Brushless DC Motor Controller - Intersil Corporation

भाग संख्या HIP4011
समारोह Three Phase Brushless DC Motor Controller
मैन्युफैक्चरर्स Intersil Corporation 
लोगो Intersil Corporation लोगो 
पूर्व दर्शन
1 Page
		
<?=HIP4011?> डेटा पत्रक पीडीएफ

HIP4011 pdf
Specifications HIP4011
Absolute Maximum Ratings
Thermal Information
Supply Voltage, SV+ or PV+. . . . . . . . . . . . . . . . . . . . . . -1V to +16V
Referred to SGND or PGND (Note 1)
Output Current, Continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A
Output Current, Peak (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . 5A
Substrate (PGND) Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1A
Logic Input Current . . . . . . . . . . . . . . . . . . . . . . . . . -20mA to +20mA
(Clamped to SV+ and SGND)
Thermal Resistance
θJA
15 Lead SIP Power Package. . . . . . . . . . 45oC/W
θJC
3oC/W
Power Dissipation (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25W
Junction Temperature Range, Operating . . . . . . . . . . . . . . . +150oC
Storage Temperature Range. . . . . . . . . . . . . . . . . . -55oC to +150oC
Power Dissipation
Up to +125oC without heat sink . . . . . . . . . . . . . . . . . . . . . 0.56W
Above +125oC without Heat Sink . . Derate Linearly at 22mW/oC
Up to +125oC with Infinite Heat Sink . . . . . . . . . . . . . . . . . 8.33W
Above +125oC with Infinite Heat Sink . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Derate Linearly at 333mW/oC
Lead Temperature (During Soldering)
At a Distance 1/16 inch ±1/32 inch (1.59mm ±0.79mm)
from Case for 10s Max. . . . . . . . . . . . . . . . . . . . . . . . . . +265oC
NOTES:
1. PV+ and SV+ are to be tied together, as are PGND and SGND.
2. Operating above the continuous current rating causes a decrease in operating life.
3. Derate power dissipation above case temperature of +75oC at 0.33 Watts/oC.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications TA = +25oC and SV+ = PV+ = 10.4V to 13.2V, Unless Otherwise Specified
PARAMETERS
TEST CONDITION
MIN TYP
SUPPLY (SV+) CURRENT
No Drive
Outputs Off
--
With Drive
Outputs On
--
LOGIC INPUT CURRENT
Sensor Inputs
SENA, SENB & SENC = 0V to 3V
-0.5 -
Brake Input
FBRK = 0.8V to 2.4V
50 -
LOGIC INPUT THRESHOLDS
Sensor Inputs
Logic “0” Input Voltage
--
Sensor Inputs
Logic “1” Input Voltage
3-
Brake Input
Logic “0” Input Voltage
--
Brake Input
Logic “1” Input Voltage
2.4 -
AMPLIFIER INPUT (SPD)
Bias Current
--
Offset Voltage
--
Input Range (Linear)
0-
Input Impedance
1-
System Bandwidth
(Note 1)
- 35
Current Limit
Rsense = 0.20
-5
THERMAL LIMIT
Threshold
- 155
Hysteresis
- 40
OUTPUT DRIVERS
On Saturation (See Note 5)
On Saturation (See Note 5)
Off Leakage
Slew Rate
IOUT = 3A, VPMOS + VNMOS
IOUT = 0.6A, VPMOS + VNMOS
PV+ > VOUT > PGND or ISEN
(See Note 2)
--
--
--
- 0.5
MAX
10
15
-1.5
150
1.8
-
0.8
-
700
3
1
-
-
-
-
-
2.2
0.44
1
-
UNITS
mA
mA
mA
µA
V
V
V
V
nA
mV
V
M
kHz
A
oC
oC
V
V
mA
V/µS
6-12

विन्यास 4 पेज
डाउनलोड[ HIP4011 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
HIP4011Three Phase Brushless DC Motor ControllerIntersil Corporation
Intersil Corporation


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English