DataSheet.in

HIP1090 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - Protected High Side Power Switch with Transient Suppression - Intersil Corporation

भाग संख्या HIP1090
समारोह Protected High Side Power Switch with Transient Suppression
मैन्युफैक्चरर्स Intersil Corporation 
लोगो Intersil Corporation लोगो 
पूर्व दर्शन
1 Page
		
<?=HIP1090?> डेटा पत्रक पीडीएफ

HIP1090 pdf
Specifications HIP1090
Absolute Maximum Ratings
Thermal Information
Input (Supply) Voltage, VIN (Control Pin Reference) . . . . . . . . ±24V
Transient Max Voltage, VIN (15ms) . . . . . . . . . . . . . . . . . . . . . ±90V
Load Current, IOUT . . . . . . . . . . . . . . . . . . . . Short Circuit Protected
Thermal Resistance
θJA
Plastic SIP Package . . . . . . . . . . . . . . . . 50oC/W
θJC
4oC/W
Maximum Power Dissipation, (Note 4)
At TA = +105oC, Infinite Heat Sink. . . . . . . . . . . . . . . . . . . 11.25W
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150oC
Ambient Temperature Range . . . . . . . . . . . . . . . . -40oC to +125oC
Storage Temperature Range. . . . . . . . . . . . . . . . . . -40oC to +150oC
Lead Temperature (Soldering During). . . . . . . . . . . . . . . . . . +265oC
1/16 ± 1/32 inch (1.59 ± 0.79mm) from case for 10s maximum
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications TA = -40oC to +125oC; VIN = 4V to 16V; VCON = GND or 0V, Unless Otherwise Specified
PARAMETERS
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNITS
Input (Supply) Voltage Operating
Range
Input Voltage Threshold for Forward
Turn-On to Load
VIN
VTHD
(Note 1); Also, See Figure 4 for
Expanding VIN Range
Load = 1k
4 - 16 V
- 2.5 -
V
Input Voltage for Output Shutdown
Output Shutdown Leakage
Output Cutoff Leakage
Thermal Shutdown Temperature
Maximum Output Transient Pulse
Current
VSHSD
(Note 2)
16 - 19 V
ILEAK1
VIN = 19V and 24V; Load = 1k
- - 100 µA
ILEAK2
VIN = 16V; Control Open; Load = 1k
-
1
-
TSD - 150 -
µA
oC
IOUT(Tran) VIN = ±90V for 15ms, VOUT = 14V
-20 - +20 mA
Maximum Control Transient Pulse
Current
ICON(Tran) VIN = ±90V for 15ms, VOUT = 14V
-50 - +50 mA
Short Circuit Current
Input-to-Output Voltage Drop
Control Current
Turn ON (Rise Time);
“Pass-Thru” Mode
ISC
ICON
tON
VIN = 4V, IOUT = 175mA
VIN = 9V, IOUT = 500mA
VIN = 16V, IOUT = 800mA
VIN = 16V, IOUT = 1A
VIN = 16V, IOUT = 100mA
VIN = 16V, IOUT = 800mA
VIN = 16V, IOUT = 1A
Switch VIN 0V(GND) to 5.5V; Mea-
sure VOUT (to 90%); Load = 1k
(Note 3)
1 - 2A
- - 0.25 V
- - 0.65 V
- - 1.05 V
- 0.8 -
V
- - 25 mA
- - 50 mA
- 50 - mA
- - 20 µs
Turn OFF (Fall Time);
“Pass-Thru” Mode
tOFF Switch VIN 5.5V to 0V(GND); Mea- - - 20 µs
sure VOUT (to 90%); Load = 1k
(Note 3)
Turn ON (Rise Time);
High Pass Switch Mode
tON See Figure 3 and Figure 4 (Note 3) - 15 - µs
Turn OFF (Fall Time);
High Pass Switch Mode
tOFF See Figure 3 and Figure 4 (Note 3) - 15 - µs
NOTES:
1. The Input Operating Voltage is not limited by the threshold of Shutdown. The VIN voltage may range to ±24V while the normal functional
switching range is typically +2.5V to +17.5V (reference to VCON).
2. The Output Drive is switched-off when the Input voltage(Supply pin), referenced to the Control pin exceeds the threshold shutdown
VSHSD or the input voltage is less than the forward turn-on threshold (Including negative voltages within the transient peak ratings).
3. TON and TOFF times include Prop Delay and Rise/Fall time.
4. The worst case thermal resistance,θJC for the SIP TO-220 is 4oC/W. The calculation for dissipation and junction temperature rise due to
dissipation is:
PD = (VIN -VOUT) + (VIN)(ICON )
TJ = TAMBIENT + (PD) (θJC) for an infinite Heat Sink.
Derating from 150oC is based on the reciprocal of thermal resistance, θJC+θHS. For example: Where θJC = 4oC/W and given θHS = 6o/W
as the thermal resistance of an external Heat Sink, the junction-to-air thermal resistance, θJA = 10oC/W. Therefore, for the maximum allowed
dissipation, derate 0.1W/oC for each degree from TAMB to the maximum rated junction temperature of 150oC. If TAMB = 100oC, the maximum
PD is (150 - 100) x 0.1W/oC = 5W.
9-23

विन्यास 5 पेज
डाउनलोड[ HIP1090 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
HIP1090Protected High Side Power Switch with Transient SuppressionIntersil Corporation
Intersil Corporation


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English