DataSheet.in

EPE6030 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - 10 Base-T Module - PCA ELECTRONICS

भाग संख्या EPE6030
समारोह 10 Base-T Module
मैन्युफैक्चरर्स PCA ELECTRONICS 
लोगो PCA ELECTRONICS लोगो 
पूर्व दर्शन
1 Page
		
<?=EPE6030?> डेटा पत्रक पीडीएफ

EPE6030 pdf
ELECTRONICS INC.
10 Base-T Module with
Enhanced Common Mode Attenuation
EPE6030
The circuit below is a guideline for interconnecting PCA’s EPE6030 with AMD 79C96X and -970, PCnet chip family as
reference controllers. Further details of system design, such as chip pin-out, etc. can be obtained from the specific chip
manufacturer.
Typical insertion loss of the isolation transformer/filter is 0.7dB. This parameter covers the entire spectrum of the encoded
signals in 10 Base-T protocols. However, the predistortion resistor network introduces some loss which has to be taken
into account in determining how well your design meets the Standard Template requirements.
Users are encouraged to verify if this network best suits their application needs with the chip manufacturer before choosing
a specific set of values. Additionally, user should make sure that these resistor values provide 802.3 Return Loss
specification complaince at either extremes of the cable impedance, namely; 85to 115. Implement only those parts in
the design that will meet this requirement.
A quick calculation of the effective Thevenin’s termination impedance for the filter follows:
R(termination)= 2(61.9//422)//1.2K100.
Thus, when measuring the return loss of these parts on the bench, it is not necessary to provide a shunting resistor across
the four outputs.
The phantom resistors shown around the RJ45 connector have been known to suppress unwanted radiation that unused
wires pick up from the immediate environment. Their placement and use are to be considered carefully before a design is
finalized.
It is recommended that there be a neat separation of ground planes in the layout. It is generally accepted practice to limit
the plane off at least 0.08 inches away from the chip side pins of EPE6030. There need not be any ground plane beyond
this point.
For best results, PCB designer should design the outgoing traces preferably to be 50, balanced and well coupled to
achieve minimum radiation from these traces.
Typical Application Circuit for UTP
10 Base-T
PHY
TX+
TXd+
TX-
TXd-
RX+
RX-
TX+
1 81
2 6 2 TX- RJ45*
3 11 3 RX+
RX-
4 96
4578
14
16 EPE6030
5 12
PCA ELECTRONICS, INC.
16799 SCHOENBORN ST.
NORTH HILLS, CA 91343
Chassis
Ground
Notes : * Pin-outs shown are for NIC configurations.
For Hubs and Repeaters swap pins 1-2 with pins 3-6.
CSE603b Rev. A 10/7/96
TEL: (818) 892-0761
FAX: (818) 894-5791
http://www.pca.com

विन्यास 2 पेज
डाउनलोड[ EPE6030 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
EPE603010 Base-T ModulePCA ELECTRONICS
PCA ELECTRONICS
EPE6030G10Base-T Interface ModulePCA ELECTRONICS
PCA ELECTRONICS


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English