DataSheet.in

AT89LP213 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - 8-bit Microcontroller - ATMEL Corporation

भाग संख्या AT89LP213
समारोह 8-bit Microcontroller
मैन्युफैक्चरर्स ATMEL Corporation 
लोगो ATMEL Corporation लोगो 
पूर्व दर्शन
1 Page
		
<?=AT89LP213?> डेटा पत्रक पीडीएफ

AT89LP213 pdf
need only 1 to 4 clock cycles providing 6 to 12 times more throughput than the standard 8051.
Seventy percent of instructions need only as many clock cycles as they have bytes to execute,
and most of the remaining instructions require only one additional clock. The enhanced CPU
core is capable of 20 MIPS throughput whereas the classic 8051 CPU can deliver only 4 MIPS
at the same current consumption. Conversely, at the same throughput as the classic 8051, the
new CPU core runs at a much lower speed and thereby greatly reduces power consumption.
The AT89LP213/214 provides the following standard features: 2K bytes of In-System Program-
mable Flash memory, 128 bytes of RAM, up to 12 I/O lines, two 16-bit timer/counters, two PWM
outputs (AT89LP213 only), a programmable watchdog timer, a full duplex serial port
(AT89LP214 only), a serial peripheral interface, an internal 8 MHz RC oscillator, on-chip crystal
oscillator, and a four-level, six-vector interrupt system.
The two timer/counters in the AT89LP213/214 are enhanced with two new modes. Mode 0 can
be configured as a variable 9- to 16-bit timer/counter and Mode 1 can be configured as a 16-bit
auto-reload timer/counter. In addition, the timer/counters on the AT89LP213 may independently
drive a pulse width modulation output.
The I/O ports of the AT89LP213/214 can be independently configured in one of four operating
modes. In quasi-bidirectional mode, the ports operate as in the classic 8051. In input mode, the
ports are tristated. Push-pull output mode provides full CMOS drivers and open-drain mode pro-
vides just a pull-down. In addition, all 8 pins of Port 1 can be configured to generate an interrupt
using the general-purpose interrupt interface. The I/O pins of the AT89LP213/214 tolerate volt-
ages higher than the device’s own power supply, up to 5.5V. When the device is supplied at
2.4V and all I/O ports receive 5.5V, the total back flowing current in all I/Os is less than 100 µA.
2. Pin Configuration
2.1 AT89LP213: 14-lead TSSOP/PDIP
(GPI5/MOSI) P1.5
(GPI7/SCK) P1.7
(GPI5/RST) P1.3
GND
(GPI2) P1.2
(T0) P3.4
(INT0/XTAL1) P3.2
1
2
3
4
5
6
7
14 P1.6 (MISO/GPI6)
13 P1.4 (SS/GPI4)
12 P1.1 (AIN1/GPI1)
11 P1.0 (AIN0/GPI0)
10 VCC
9 P3.5 (T1)
8 P3.3 (XTAL2/CLKOUT/INT1)
2.2 AT89LP214: 14-lead TSSOP/PDIP
(GPI5/MOSI) P1.5
(GPI7/SCK) P1.7
(GPI5/RST) P1.3
GND
(GPI2) P1.2
(RxD) P3.0
(INT0/XTAL1) P3.2
1
2
3
4
5
6
7
14 P1.6 (MISO/GPI6)
13 P1.4 (SS/GPI4)
12 P1.1 (AIN1/GPI1)
11 P1.0 (AIN0/GPI0)
10 VCC
9 P3.1 (TxD)
8 P3.3 (XTAL2/CLKOUT/INT1)
2 AT89LP213/214
3538E–MICRO–11/10

विन्यास 30 पेज
डाउनलोड[ AT89LP213 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
AT89LP2138-bit MicrocontrollerATMEL Corporation
ATMEL Corporation
AT89LP2148-bit MicrocontrollerATMEL Corporation
ATMEL Corporation


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English