DataSheet.in

DSC2041 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - Low-Jitter Configurable Dual HCSL-CMOS Oscillator - Micrel

भाग संख्या DSC2041
समारोह Low-Jitter Configurable Dual HCSL-CMOS Oscillator
मैन्युफैक्चरर्स Micrel 
लोगो Micrel लोगो 
पूर्व दर्शन
1 Page
		
<?=DSC2041?> डेटा पत्रक पीडीएफ

DSC2041 pdf
DSC2041
Low-Jitter Configurable Dual HCSL-CMOS Oscillator
Pin Description
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Pin Name
Enable
NC
OS0
GND
FS0
FS1
FS2
Output1+
Output1-
OS1
Output 2
VDD2
VDD
OS2
Pin
Type
I
NA
I
Power
I
I
I
O
O
I
O
Power
Power
I
Description
Enables outputs when high and disables (tri-state) them when low
Leave unconnected or grounded
Least significant bit for output drive strength selection for CMOS
Ground
Least significant bit for frequency selection
Middle bit for frequency selection
Most significant bit for frequency selection
Positive HCSL Output 1
Negative HCSL Output 1
Middle bit for output drive strength selection for CMOS
CMOS output
Power Supply 2 for CMOS Output
Power Supply
Most significant bit for output drive strength selection for CMOS
Operational Description
The DSC2041 is a dual output HCSL-CMOS
oscillator consisting of a MEMS resonator and
a support PLL IC. The two outputs, CMOS and
HCSL, are generated through independent 8-
bit programmable dividers from the output of
the internal PLL. Two constraints are imposed
on the output frequencies: 1) f2=M x f1/N,
where M and N are even integers between 4
and 254, 2) 1.2GHz < N x f2 < 1.7GHz.
The actual frequencies output by the DSC2041
are controlled by an internal pre-programmed
memory (OTP). This memory stores all
coefficients required by the PLL for up to eight
different frequency combinations. Three
control pins (FS0 FS2) select the output
frequency combination. Discera supports
customer defined versions of the DSC2041.
Standard frequency options are described in in
the following sections.
The DSC2041 provides control of the output
voltage levels of the CMOS output. VDD2 (pin
12) sets the high voltage level of Output 2 and
must be equal to or less than VDD at all times
to insure proper operation. VDD2 can be as
low as 1.65V.
When Enable (pin 1) is floated or connected to
VDD, the DSC2041 is in operational mode.
Driving Enable to ground will tri-state both
output drivers (hi-impedance mode).
The DSC2041 has programmable output drive
strength for CMOS output. Using three control
pins (OS0-OS2), the drive strength for CMOS
output (output 2) can be adjusted to match
circuit board impedances to reduce power
supply noise, overshoot/undershoot and EMI.
Table 1 displays typical rise / fall times for the
output with a 15pf load capacitance as a
function of these control pins at VDD=3.3V
and room temperature.
Table 1. Rise/Fall times for drive strengths
Output Drive Strength Bits
[OS2, OS1, OS0] - Default [111]
000 001 010 011 100 101 110 111
tr (ns) 2.1 1.7 1.6 1.4 1.3 1.3 1.2 1.1
tf (ns) 2.5 2.4 2.4 2 1.8 1.6 1.3 1.3
_____________________________________________________________________________________________________________________________ _________________
DSC2041
Page 2
MK-Q-B-P-D-12042611-2

विन्यास 6 पेज
डाउनलोड[ DSC2041 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
DSC2040Low-Jitter Configurable HCSL OscillatorMicrel
Micrel
DSC2041Low-Jitter Configurable Dual HCSL-CMOS OscillatorMicrel
Micrel


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English